On this page below you might get lots of good additional info on the subject of A Step-by-Step Guide to Installing a Bathtub.
![How to Install a Bathtub: Install an Acrylic Tub and Tub Surround](https://www.berkeys.com/wp-content/uploads/2016/12/Bathtub-Installation.jpg)
Setting up a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently available, the project can move immediately; if you need to open up a wall surface to remove the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub and also set in the brand-new one. See to it you have certified yourself for the work and fit trying it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to consider using one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This article will certainly assist you install a brand-new bath tub in your shower room if you have currently gotten a new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your devices and material checklist ought to comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Using the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub till the level reviews degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and also inspect all joints and also new pipework for leakages as well as tighten them if necessary. Fill the tub and likewise inspect the overflow electrical outlet as well as the typical outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the tub must wait until the bath tub has actually been used a minimum of when as this will resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the supplier given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath and the tiling, bring about problems with dampness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Tools You Need to Install a New Bathtub ? Try leaving feedback down below. We'd be glad to find out your opinion about this write-up. We hope to see you back again soon. For those who appreciated our article kindly remember to share it. Thank you so much for going through it.
Schedule Here